Full House Wiring Diagram:

This diagram shows how to make a full house wiring diagram. In this circuit diagram, we simply use, a single-phase energy meter, a DP MCB ( Double Pole Miniature Circuit Breaker ), an RCCB ( Residential Current Circuit Breaker ), five SP MCB ( Single Pole Miniature Circuit Breaker ), a busbar, three 3-pin power socket, five lights, four normal switches, two 2-way switches, a water pump, a water heater, etc. This diagram is very easy to connect. If you want to check how to connect this circuit please check our youtube video for more clear information.

Diagram of Full House wiring:

Components needed For this Project:

You can get the components from any of the sites below:

Single Phase Energy Meter [See Buy Click Amazon]
DP MCB 32A [See Buy Click Amazon]
SP RCCB 32A [See Buy Click Amazon]
SP MCB 10A [See Buy Click Amazon]
Busbar wire [See Buy Click Amazon]
Gang Socket [See Buy Click Amazon]
Gang Switch [See Buy Click Amazon]
2 way switch [See Buy Click Amazon]
CFL Light [See Buy Click Amazon]
Single Phase Motor (1 HP) [See Buy Click Amazon]
Geyser Water Heater [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

Components used to make the Full House Wiring Diagram:

01. Single Phase Energy Meter:

A Single-Phase Energy Meter is a sort of Watt-Hour meter. It consists of two Electromagnets. Single-Phase Energy Meter is also Popularly known as a watt-hour meter. 1 Magnet is called the shunt magnet Ml which is Mounted with a Pressure coil. The Pressure coil is a long coil Made of fine Copper wire that is connected across the Supply single-phase line. Single-phase energy meters are suitable for measuring single-phase AC current flow frequencies of 50/60 Hz, which are used for fixed indoor installation systems.

02. DP MCB:

DP MCB In 2 Pole MCB, switching & protection is affected in phases and the neutral. A Double Pole or DP Switch is a Switch that Controls 2 Circuits at the same time. In terms of Residential Switching, this Normally means it Switches the live and Neutral at the same time. In Layperson Terms, Double Pole switches or DP Switches are Exclusively Designed to Control 2 Different Electrical Circuits at the same time, which allows the Appliances to Isolate safely and reliably. Fan or light Combinations and Medical Equipment are some of the many applications for DP Electrical Switches and Electrical components.

03. RCCB:

The Residual Current Circuit breaker RCCB is the Safest device to detect and Trip against Electrical Leakage current. This ensures protection against Electric shock Caused by indirect contact. Circuit breakers (CB) are automatically Operated Electrical Switches that Protect Electrical Circuits from Short-Circuiting or Overloading systems. It Protects against many major accidents. RCCB Circuit Breaker is an Electrical Wiring device whose function is to disconnect the current in the circuit.

04. SP MCB:

In single-pole MCB, Switching and protection are Affected in only one Phase. Single phase supply to break the phase only. A single Pole breaker is Typically used with 120-volt Circuits, and a 6-20 amps Miniature Circuit Breaker. They are constructed with one Line Wire and one Neutral wire. A Single Pole switch is the most basic General-Purpose switch that you use to Control a light or another device from one location. These Switches have 2 Brass-Colored screw Terminals Connected to the hot Power source wires. Pole refers to the number of Circuits Controlled by the Switch SP Switches Control only one Switch Electrical Circuit.

05. Busbar:

A busbar is a type of Electrical conductor. It is made of copper brass or aluminum. Busbar is most commonly used in factories. We supply the power from the transformer to the busbar. We take the electricity from this busbar to the circuit breaker. The advantage of using a busbar is that through it we can provide multiple power connections in multiple places very easily. How many thick copper bars are aggregates of busbars? A copper bar is rectangular (rectangular) copper type or triangular in shape.

06. 3-Pin Socket:

A Power Socket is a Device to Which Electrical Devices Can Be Connected to Receive the Electric Current Required For Their Operation. Connected by a System of Cables to a Power Source, Usually, an Electricity Generation Facility operated by an energy Production company, generally has no moving parts. Instead, it contains metal strips that make contact with the prongs of an Electric plug inserted into the socket. It is Through these Contacts That the Electric current is Transmitted. Electrical Devices that connect to a Power Source Through a Power Socket are Considered to be Portable Because they can easily be Connected and Disconnected From the Power Source.

07. Switch:

An SPST (Single Pole Single Throw) Switch is a Switch That only Has a Single Input and can Connect Only to one Output. This means it Only Has one Input Terminal and Only 1 Output Terminal. A Switch is a Mechanical or Controlling Device That Changes the Flow of Current Direction or Interrupts the Flow of Current Within a Circuit diagram. An electrical line using Single Pole Single Throws (SPST) is Perfect for on-off switching. When the SPST is closed, the Circuit is Closed and the light from the lamp switches on the system. When The Single Pole Single Throw (SPST) is then opened, the light from the lamp goes out and the Circuit is off.

08. 2-Way Switch:

The 2-Way Switch has a wire connection system. It is a type of switch that has three wire connections. And it really has no off or on. Both sides can be turned on or off depending on how you connect one to the other. The connection of the two-way switch is different. If you use it as a changer, then put the load in the middle one and two separate lines in the upper and lower ones. The two-way switch is a type of multiway switch. Multiway switches have more points and can be controlled in multiple ways simultaneously.

09. Light:

CFL stands for Compact Fluorescent Lamp which is an improved version of tube lights of earlier days. Like tube lights, it is a vacuum glass tube with fluorescent powder coating which is not as long and straight as tube lights but curved/twisted compact, or small in size. Like a tube light, it has electrodes or filaments at both ends. But in this case, instead of a choke, there is an electronic circuit that drives the Compact Fluorescent Lamp. Because the red wave is less in the light of the Tubelight and Compact Fluorescent Lamp, the object looks a little pale or the correct color of the object does not appear.

10. Single Phase Motor:

A Single-Phase Motor is an Electrically-Powered Rotary Machine That Can Turn Electric Energy into Mechanical Energy. It Works by Using a Single-Phase Power Supply. Single-phase Motors Are Used in Equipment And Machines That Are Smaller in Size And Require Lower Horsepower. This Includes Equipment Such As Refrigerators, Pumps, Compressors, Fans, and Portable Drills. Single-phase motors Have a Similar Construction to The 3-phase Motor, Including an AC Winding That is Placed on The Stator And Short-Circuited Conductors That are Placed in a Cylindrical Rotor.

11. Water Heater:

Water Heaters are Familiar Fixtures in Most Homes. The water Heater Design That is most Widely used in the U.S. Today is Really a Pretty Simple Appliance; it is basically a Drum filled With Water And Equipped With a Heating Mechanism On The Bottom or Inside. Common Energy Sources for Heating Up Water Include Electricity, Burner oil, And Natural gas. Some Modern Applications have also Moved to solar and Geothermal Heat for Increased Efficiency controller systems. Electric Water Heaters Have Heating Elements Inside the Tank to Heat the Water.

Thank You for visiting the website. Keep visiting for more Updates.

Frequently asked questions

What is the formula for calculating cable length?

The formula when using one load cell is as follows: The maximum cable length = the allowable cable resistance ÷ the cable resistance per meter.

What is the formula for the current and length of a wire?

The magnitude of the power supply force on a wire carrying current I with length L in a magnetic field is given by the Circuit diagram equation F=ILBsinθ where θ is the angle between the wire and the magnetic Currenttlou field.

How do you calculate Ampere in a wire?

When spelled out, it means voltage = current x resistance, volts = amps x ohms, or V = A x Ω. If two of these values are known, technicians can reconfigure Ohm's Law to calculate the third.

What is the difference between watts and kVA?

Watts (W) and kilowatts (kW) are units of measurement for real power, while kilovolt-amperes (kVA) is a unit of measurement for apparent power. Real power is the power that is actually doing work, while apparent power is the power that is available to do work.

What does 60Hz mean in electricity?

A 60Hz electrical system means that the power supply completes 60 cycles of complete wave sequence per second while 50Hz means that it completes 50 cycles per second. 60Hz is usually on associated with 440, 460, 480, & 600 voltages.

← Previous Next →

Full House Wiring Diagram