Geyser wiring diagram:

This diagram shows how to make a Geyser wiring diagram. In this circuit, we use a geyser water heater, a heater element, a thermostat switch, an auto cut-off controller, and a DP MCB ( Double Pole Miniature Circuit Breaker ). First, we need to input power to DP MCB, then from DP MCB to connect the phase line in the auto cutoff controller, then from the auto cutoff controller to the input phase line thermostat, then input line to the heater element from the thermostat. Now this circuit is ready for use. If you want to know more about this circuit please check our youtube video below the post.

Diagram of Geyser wiring:

Components needed For this Project:

You can get the components from any of the sites below:

DP MCB 20A [See Buy Click Amazon]
Thermostat Switch [See Buy Click Amazon]
Geyser Water Heater [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

Components used to make the Geyser wiring diagram:

01. DP MCB:

DP MCB In 2 Pole MCB, switching & protection is affected in phases and the neutral. A Double Pole or DP Switch is a Switch that Controls 2 Circuits at the same time. In terms of Residential Switching, this Normally means it Switches the live and Neutral at the same time. In Layperson Terms, Double Pole switches or DP Switches are Exclusively Designed to Control 2 Different Electrical Circuits at the same time, which allows the Appliances to Isolate safely and reliably. Fan or light Combinations and Medical Equipment are some of the many applications for DP Electrical Switches and Electrical components.

02. Thermostat Switch:

Meaning of Thermostat The word thermo means heat and with the help of heat the Electrical circuit is switched on and off is called a thermostat. The thermostat switch is the control device of the fridge/refrigerator. which directly or indirectly controls one or more heat sources and cooling systems to maintain the refrigerator is required temperature. The role of the thermostat is important to automate the cooling system of the fridge/refrigerator. A thermostat switch is a sensitive device that automatically converts the temperature of the refrigerator.

03. Geyser:

Water Heaters are Familiar Fixtures in Most Homes. The water Heater Design That is most Widely used in the U.S. Today is Really a Pretty Simple Appliance; it is basically a Drum filled With Water And Equipped With a Heating Mechanism On The Bottom or Inside. Common Energy Sources for Heating Up Water Include Electricity, Burner oil, And Natural gas. Some Modern Applications have also Moved to solar and Geothermal Heat for Increased Efficiency controller systems. Electric Water Heaters Have Heating Elements Inside the Tank to Heat the Water.

Thank You for visiting the website. Keep visiting for more Updates.

Frequently asked questions

Which MCB is required for a geyser?

If it is a Single-phase 230 Volt system with about 10% Voltage Regulation and 75% Maintenance Factor... a 2000 Watt Geyser needs 13.334 Amp or 16 Amp MCB (next and Higher Size). the power supply However, a Geyser is not likely to be overloaded. Hence 16A or 20A will not make much difference for the clearing of Short Circuits Diagram.

Can we use MCB for the geyser?

Considering the power supply relation between water and electricity, ensure proper electrical safety before installing a geyser. For this reason, you must connect the geyser connection with the Miniature Circuit Breaker (MCB). This will save your geyser in case there is any power supply fluctuation.

How many amps are required for a geyser?

At 220 volts, a 1500-watt geyser would require approximately 6.8 amperes of electrical current (1500 watts / 220 volts = 6.8 amps), while a 4500-watt geyser would require approximately 20.5 amperes of electrical and current (4500 watts / 220 volts = 20.5 amps).

How many amps should a geyser breaker be?

A usual house DB will have a rated main circuit diagram breaker (“main switch”) of 60A. Light circuit diagrams are normally 10A, geyser circuits 15/20A, plug circuits 15/20A, and stove circuit diagrams 35A.

Is 16a enough for a geyser?

As per the current rating, the Geyser requires a current greater than 6 amps. Providing 6 amps switch sockets instead of 16 amps will lead to a damaged switch socket board and frequent tripping off MCB due to overheating. Hence, it can create electrical & safety hazards if not rectified on time.

← Previous Next →

Geyser wiring diagram