Single Phase Split AC Wiring Diagram:

This diagram shows how to make Single Phase Split AC Wiring Diagram. In this circuit diagram, we use a single-phase split indoor and outdoor AC, a DP MCB ( Double Pole Miniature Circuit Breaker ), and a Switch. First, we need to input power to DP MCB, then input power to switch from DP MCB. Then connect the split ac to the power source. Now this circuit is ready for use. If you want to know more about this circuit please check our youtube video below the post.


Diagram of Single Phase Split AC Wiring Diagram:

Single Phase Split AC Wiring Diagram

Components needed For this Project:

You can get the components from any of the sites below:

  1. DP MCB 25A [See Buy Click Amazon]
  2. DP 20A Switch [See Buy Click Amazon]
  3. Air Conditioner [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:


Components used to make the Single Phase Split AC Wiring:

01. DP MCB:

DP MCB In 2 Pole MCB, switching & protection is affected in phases and the neutral. A Double Pole or DP Switch is a Switch that Controls 2 Circuits at the same time. In terms of Residential Switching, this Normally means it Switches the live and Neutral at the same time. In Layperson Terms, Double Pole switches or DP Switches are Exclusively Designed to Control 2 Different Electrical Circuits at the same time, which allows the Appliances to Isolate safely and reliably. Fan or light Combinations and Medical Equipment are some of the many applications for DP Electrical Switches and Electrical components.

02. DP Switch:

20 amp Double Pole Switches are generally used with Electrical appliances that need to be hard-wired as opposed to using a Plug and power Socket. Double pole switches make it possible to isolate appliances safely from the power supply source. double pole switches or DP switches are exclusively designed to control 2 different electrical circuits at the same time.

03. Indoor, Outdoor AC:

The Indoor Unit is What you Will typically Find Mounted on a Wall set. The Outdoor Unit is Mounted Either on an Exterior wall or Placed at the GND Level. The Outdoor Unit Will typically be in a Slab of Concrete. This Unit is Where the Heat is Expelled From the House used. After the Indoor Unit Pulls The Heat and Moisture From The Air Inside your Home. It transfers The Heat via The Refrigerant to the outdoor unit side. Cooler Temperatures, and lower humidity. With all Air Conditioning Components Located Outside, you Can keep cool With a Virtually Invisible, Silent System.

Thank You for visiting the website. Keep visiting for more Updates.

Frequently asked questions

Can we use 1.5-ton AC in a single phase?

Single-phase connection is no problem at all. The 1.5-ton AC will also run on a single phase only.

How many split ACs can run on a single phase?

Yes, you can install two air conditioners of 1.5 tons each with a single-phase supply of 230V, 50Hz. However, it's important to ensure that the electrical circuit and wiring can accommodate the combined load of both air conditioners to prevent overloading and potential safety hazards.

How many ACs can run in single-phase current?

only one. if two will run then there is a major chance of a short circuit.

What is the best MCB for a 1.5-ton AC unit?

A typical 1.5-ton AC unit has a cooling capacity of around 4,500 watts or operates at 240v. So, 4,500W / 240V equals 18.75 Amps. To ensure safety and accommodate startup surges, a 20A switch or circuit diagram breaker is recommended for a 1.5-ton AC unit.

Can 1-ton AC run on a single phase?

Every air conditioner works with a single-phase supply whether it is 1 Ton 1.5 ton or 2 tons.

Read more Single Phase Wiring


Submit a Comment

Your email address will not be published. Required fields are marked *