How To Make Sub-Distribution Board Wiring

Electrical, single phase Line Wiring | 0 comments

Basic Electrical
Power System
House Wiring
Motor Wiring
Industrial Wiring
Basic Electronic
Electronic Project
Electronic Mini Project
Digital Logic Gate
Arduino Project
Microcontroller Board
Electronic Sensor
Electronic Module
Electronic Display

Sub Distribution Board Wiring:

This diagram shows How To Make Sub Distribution Board Wiring. In this circuit diagram, we use a single-phase energy meter, a DP MCB (Double Pole Miniature Circuit Breaker ), an SPD ( Surge Protection Device ), four SP MCB ( Single Pole Miniature Circuit Breaker ), a neutral and an earthing busbar. First, we need to input the power line into the energy meter, then connect DP MCB with the energy meter. Then connect the SPD and SP MCB, also need to connect the neutral and earthing busbar. Now our circuit is ready for use. If you want to know more about this circuit please check our youtube video below the post.

Advertisements

Diagram of Sub Distribution Board Wiring:

How To Make Sub Distribution Board Wiring

Components needed For this Project:

You can get the components from any of the sites below:

  1. Single Phase Energy Meter [See Buy Click Amazon]
  2. DP MCB 32A [See Buy Click Amazon]
  3. DP SPD 20KA [See Buy Click Amazon]
  4. SP MCB 10A [See Buy Click Amazon]
  5. Busbar wire [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

Advertisements

Components used to make the Sub Distribution Board Wiring:

01. Single Phase Energy Meter:

A Single-Phase Energy Meter is a sort of Watt-Hour meter. It consists of two Electromagnets. Single-Phase Energy Meter is also Popularly known as a watt-hour meter. 1 Magnet is called the shunt magnet Ml which is Mounted with a Pressure coil. The Pressure coil is a long coil Made of fine Copper wire that is connected across the Supply single-phase line. Single-phase energy meters are suitable for measuring single-phase AC current flow frequencies of 50/60 Hz, which are used for fixed indoor installation systems.

02. DP MCB:

DP MCB In 2 Pole MCB, switching & protection is affected in phases and the neutral. A Double Pole or DP Switch is a Switch that Controls 2 Circuits at the same time. In terms of Residential Switching, this Normally means it Switches the live and Neutral at the same time. In Layperson Terms, Double Pole switches or DP Switches are Exclusively Designed to Control 2 Different Electrical Circuits at the same time, which allows the Appliances to Isolate safely and reliably. Fan or light Combinations and Medical Equipment are some of the many applications for DP Electrical Switches and Electrical components.

03. SPD:

The ability of an SPD to limit overvoltage in the Electrical distribution network by diverting the surge current is the surge-protective component, the mechanical structure of the SPD, and the connection to the electrical distribution network. A surge protection device SPD is a component of an electrical installation protection system. This device is connected to the power supply in parallel with the load circuit it is intended to protect. It can be used at all levels of the Power Supply Network. It is widely used in overvoltage protection.

04. SP MCB:

In single-pole MCB, Switching and protection are Affected in only one Phase. Single phase supply to break the phase only. A single Pole breaker is Typically used with 120-volt Circuits, and a 6-20 amps Miniature Circuit Breaker. They are constructed with one Line Wire and one Neutral wire. A Single Pole switch is the most basic General-Purpose switch that you use to Control a light or another device from one location. These Switches have 2 Brass-Colored screw Terminals Connected to the hot Power source wires. Pole refers to the number of Circuits Controlled by the Switch SP Switches Control only one Switch Electrical Circuit.

05. Busbar:

A busbar is a type of Electrical conductor. It is made of copper brass or aluminum. Busbar is most commonly used in factories. We supply the power from the transformer to the busbar. We take the electricity from this busbar to the circuit breaker. The advantage of using a busbar is that through it we can provide multiple power connections in multiple places very easily. How many thick copper bars are aggregates of busbars? A copper bar is rectangular (rectangular) copper type or triangular in shape.

Thank You for visiting the website. Keep visiting for more Updates.

Read more Single Phase Wiring

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *


Join our Youtube Channels to stay updated with the latest Electronic and Electrical Projects and exclusive updates.


Electronic Experiment Youtube Channel: Join Now

Advertisements