Water Pump Control From Two Places:

This diagram shows how to make Water Pump Control From Two Places. In this circuit, we use a single-phase water pump motor, an indicator light, and two 2-way switches. First, we need to input the phase line to 2-way switch two, then connect with one and two like our diagram, connect the indicator light with a power source, and lastly connect the water pump with the power source. Now our circuit is ready for use. If you want to know more about this circuit please check our youtube video below the post.


Diagram of Water Pump Control From Two Places:

Water Pump Control From Two Places

Components needed For this Project:

You can get the components from any of the sites below:

  1. 2 way switch [See Buy Click Amazon]
  2. Board Indicator [See Buy Click Amazon]
  3. Single Phase Motor (1 HP) [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:


Components used to make the Water Pump Control From Two Places:

01. 2-Way Switch:

The 2-Way Switch has a wire connection system. It is a type of switch that has three wire connections. And it really has no off or on. Both sides can be turned on or off depending on how you connect one to the other. The connection of the two-way switch is different. If you use it as a changer, then put the load in the middle one and two separate lines in the upper and lower ones. The two-way switch is a type of multiway switch. Multiway switches have more points and can be controlled in multiple ways simultaneously.

02. Indicator:

Board indicators are optoelectronic devices that emit light to show the operating condition of a machine or appliance. Manufacturers and distributors use various terminologies for this type of product which can be confusing when trying to power source an item, particularly on-line: Signal lamps. Signal lights. That is an example of an indicator light bulb.

03. Single Phase Motor:

A Single-Phase Motor is an Electrically-Powered Rotary Machine That Can Turn Electric Energy into Mechanical Energy. It Works by Using a Single-Phase Power Supply. Single-phase Motors Are Used in Equipment And Machines That Are Smaller in Size And Require Lower Horsepower. This Includes Equipment Such As Refrigerators, Pumps, Compressors, Fans, and Portable Drills. Single-phase motors Have a Similar Construction to The 3-phase Motor, Including an AC Winding That is Placed on The Stator And Short-Circuited Conductors That are Placed in a Cylindrical Rotor.

Thank You for visiting the website. Keep visiting for more Updates.

Frequently asked questions

What are the two parts of a water pump?

A water pump consists of a water pump housing (1), inside that, the following of parts are found:? a shaft with a flange (2);? the bearing (3), into which the shaft is fitted;? the impeller (4), that is attached to the bottom of the shaft;? two ceramic seals.

What is a 2-stage water pump?

Two-stage pumps have two impellers on a common shaft, or both impellers have a single eye. There are 2 modes of operation, capacity, which also is called parallel, and pressure, which also is called series. The operation of the modes describes how the pump impellers operate.

What is a dual water pump?

The dual pump system has 2 pumps in place, which alternate between each other at every start-up and would turn both on at the same time during a high-water level or record-breaking storm.

What is HP in a water pump?

Water horsepower supply is the minimum power that is required to move the water (Figure 2). In other words, it is the power supply that the pump would require if the pump were 100% efficient. The water horsepower supply can be determined if the flow rate of the water and the force (pressure) required to produce that flow are known.

How do you adjust water flow?

The aerator typically has a screen and a flow restrictor that can be adjusted to control the flow rate. Unscrew the aerator from the faucet spout, and you may find a flow restrictor or a screw that could be turned to increase or decrease the water flow. Adjusting this component could help regulate the speed of the water.

Read more Single Phase Wiring


Submit a Comment

Your email address will not be published. Required fields are marked *