3 Phase Star Delta Motor Wiring:
This diagram shows how to make 3-Phase Star Delta Motor Wiring. In this circuit, we use a total of three magnetic contactors, an NC ( Normal Close ) switch, an NO ( Normal Close ) switch, an SP MCB ( Singel Pole Miniature Circuit Breaker ), a TP MCB ( Tripple Pole Miniature Circuit Breaker ), a digital timer, and a 3 phase motor. This diagram is very simple and easy to make. If you want to know more about this circuit diagram please check our youtube video in the below post.
Components needed For this Project:
You can get the components from any of the sites below:
- 3-Phase Motor [See Buy Click Amazon]
- Magnetic Contactor [See Buy Click Amazon]
- TP MCB [See Buy Click Amazon]
- 8-Pin Timer [See Buy Click Amazon]
- SP MCB [See Buy Click Amazon]
- NC Switch [See Buy Click Amazon]
- NO Switch [See Buy Click Amazon]
*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!
Components used to make the 3 Phase Star Delta Motor Wiring:
A Three-Phase electric motor uses a 3-Phase Power Supply to Convert Electric Energy into Mechanical Energy. It contains four Wires (Three hot Wires and one Neutral Wire) and Uses 3 Alternating Currents of the Same Frequency. Since it Generates a Rotating Magnetic Field, it does not need a Capacitor for the Startup. Some Three-Phase Motors are Reversible, Which Means they can serve as Generators by Turning Mechanical Energy into Electrical Energy.
02. Magnetic Contactor:
A magnetic contactor is an electromagnetic switching device. It is generally used for controlling three-phase motors. The operation of a magnetic contactor is similar to that of a relay, but a relay is used for low-power or low-voltage connections, and a magnetic contactor is used for high-power or high-voltage connections. As soon as the supply is applied to the magnetic contactor coil, its normally open contacts are closed and normally closed contacts are opened and the associated devices are also operated. This is how a magnetic contactor works.
The full meaning of MCB is Miniature Circuit Breaker. MCB is an electromagnetic switch or device. If for any reason a short circuit occurs in the supply line or load line (line to line or line to neutral) or in case of overload, the MCB automatically trips and disconnects the main line circuit or household power Connection. TP MCB In Three Pole MCB, Switching & Protection is affected in only Three-Phases and the Neutral is not part of the MCB. 3 pole MCB signifies the Connection of Three Wires for a Three-Phase system R-Y-B Phase. Three-Phase Supply Only Without Neutral.
04. 8-Pin Timer:
A timer is a type of time switching device that controls and controls electrical circuits and electrical and electronics devices through time setting (on/off). Timer is basically 8 pin. Like other controlling devices the timer has a coil and when this coil is magnetized, the timer works on/off. The timer has two common ends and each common end has normally close and normally open options. When the timer is set by time, the timer trips at the end of that time and turns the common’s normally closed (on) to open (off) and normally open (off) to close (on). This is how the timer works.
In single-pole MCB, Switching & Protection is Affected in only one Phase. Single phase supply to break the phase only. A single Pole breaker is Typically used with 120-volt Circuits, 15-20 amps. They are constructed with one Hot Wire and one Neutral wire. An SP switch is the most basic General-Purpose switch that you use to Control a light or another device from one location. These Switches have two Brass-Colored screw Terminals Connected to the hot Power source wires. Pole refers to the number of Circuits Controlled by the Switch SP Switches Control only one Electrical Circuit.
06. NC Switch:
An NC (Normally Closed) Push Button is a Push Button That, In Its Default State, Makes Electrical Contact With The Circuit. An NC (Normally Closed) Push Button is a Push Button that, in its Default State, Makes electrical Contact With the Circuit. When The Button Is Pressed Down, The Switch no Longer Makes Electrical Contact And The Circuit is Now Open. When The Button is Not Pressed, Electricity Can Flow, But When it is Pressed The Circuit is Broken. This type Of Switch is Also known As a Normally Closed (NC) Switch.
NO (Normally Open) Terms Refer to a Type of Dry Contact or Wet Contact. A ‘Push to Make’ Switch Allows Electricity to flow Between its two contacts when held in. When the button is released, the Circuit is broken. This type of Switch has also known as A Normally Open (NO) Switch. As its name implies, a Normally Open (NO) Switch Contact or “a Contact” is a Switch. Put very simply, a Normally Open Sensor will have no Current When in a Normal State But When it Enters an Alarm State it will have +5V applied to the Circuit.
Watch to Youtube:
Thank You for visiting the website. Keep visiting for more Updates.
Read more Single Phase Wiring
Single Phase Wiring
Single Phase Distribution Board Wiring Ampere meter in Voltmeter Wiring Forward Reverse Motor Control Diagram...
Relay in Lamp Wiring
Relay in Lamp Wiring: This diagram shows how to make a relay in lamp wiring. In this circuit, we use an 8-pin relay,...
RCCB With MCB Wiring Diagram
RCCB With MCB Wiring Diagram: This diagram shows how to make a connection to RCCB with MCB wiring. In this circuit, we...
0 Comments