Hybrid Solar Wind System Diagram:

This circuit diagram shows how to make a connection hybrid solar wing system. In this circuit diagram, we use a dump load resistor, two solar panels, two 12v batteries, a solar charge controller, and a solar wind turbine. This diagram is very easy to make. Here we need to connect the solar panel and wind turbine to the solar charge controller, then connect the batteries to the charge controller. Now this circuit is ready for use. If you need more clear details about this circuit please check our animation video for more clear details about this circuit connection making.

Diagram of Hybrid Solar Wind System Diagram:

Components needed For this Project:

You can get the components from any of the sites below:

Solar Panel [See Buy Click Amazon]
Solar Charge Controller [See Buy Click Amazon]
Wind Turbine [See Buy Click Amazon]
12V Battery [See Buy Click Amazon]
Dump Load Resistor [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

Components used to make the Hybrid Solar Wind System Diagram:

01. Solar Panel:

Solar Panel is a Device That Converts Light From the Sun, Which is Composed of Particles of Energy Called, into Electricity that can be Used to Power Electrical Loads. Solar panels Collect Clean Renewable Energy in the Form of Sunlight and Convert that Lamp into Electricity Which can Then be Used to Provide Power for Electrical Loads. Solar Panels Are Comprised of Several Individual Solar Cells Which are Composed of Layers of Silicon, which provides the negative charge, and boron. Solar Panels Absorb the Photons And in Doing so Initiate an Electric Current.

02. Solar Charge Controller:

A solar Charge Controller is an Electronic Device That Manages the Power Going into the Battery Bank from the Solar Array. It Ensures That the Deep cycle Batteries are not Overcharged During the day and That the power doesn’t run back to the Solar Panels overnight and Drain the batteries. A Solar Charge Controller Manages the Power Going into the Battery Bank From the Solar Array. Some Charge Controllers are Available with Additional Capabilities, load Control, and Lighting, but Managing the power is its Primary Job. A Solar Charge Controller is Available in two Different Technologies, PWM and MPPT.

03. Wind Turbine:

Solar Charge Controller is an Electronic Device That Manages the Power Going into the Battery Bank from the Solar Array. It Ensures That the Deep cycle Batteries are not Overcharged During the day and That the power doesn’t run back to the Solar Panels overnight and Drain the batteries. A Solar Charge Controller Manages the Power Going into the Battery Bank From the Solar Array. Some Charge Controllers are Available with Additional Capabilities, load Control and like Lighting, but Managing the power is its Primary Job. A Solar Charge Controller is Available in two Different Technologies, PWM and MPPT.

04. 12v Battery:

A 12V Battery is Available As a Non-Rechargeable Alkaline Battery Or In Rechargeable Forms. This Battery is Often Used in Various Outdoor Applications that Require Greater Amounts of Energy in Order to Operate as Desired. 12V Battery is a Name Given to a Unique Style of Battery, but its Voltage is More Than 12 Volts. In Such Cases Where a 12V Portable Battery is Used to Replace an onboard 12-volt Battery, It Is Usually Lighter Than a Standard Version. This is Because It is more likely to be Transported Between Uses and Consumers Will Not Choose to Carry a Large, Bulky Battery. A Portable 12V Battery is Usually Sealed in a case so That it is Waterproof.

05. Dump Load Resistor:

This Divert Load Resistor is for use to Divert the Excess Power being Generated when wind Turbine Generator Batteries are full and can be run at 100% duty cycle due to the quality Double wire Wound design. It can also be Used With a Solar Array. This Is a Practical Accessory For The Dump Load Resistor. Dump load Resistor When the load is over, the Controller will Automatically cut off the Power to avoid Damage to the Battery and the Load due to Too High Current.

Thank You for visiting the website. Keep visiting for more Updates.

← Previous Next →

Hybrid Solar Wind System Diagram