8 pin timer tasting wiring:

This diagram shows how to make 8-pin timer-tasting wiring. In this circuit, we use. In this circuit, we use a DP MCB ( Double Pole Minature Circuit Breaker ), an 8-pin relay, and three indicator lights. This circuit is very simple and easy to make. if you want to know more about this circuit please check our youtube video belwo the post. Stay with our website for more updates.


Diagram of 8 pin timer tasting wiring:

8 pin timer tasting wiring

Components needed For this Project:

You can get the components from any of the sites below:

  1. DP MCB 25A [See Buy Click Amazon]
  2. 8 Pin Timer 220V AC [See Buy Click Amazon]
  3. Indicator Light 220v AC [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:


Components used to make the 8 pin timer tasting wiring:

01. DP MCB:

DP MCB In 2 Pole MCB, switching & protection is affected in phases and the neutral. A Double Pole or DP Switch is a Switch that Controls 2 Circuits at the same time. In terms of Residential Switching, this Normally means it Switches the live and Neutral at the same time. In Layperson Terms, Double Pole switches or DP Switches are Exclusively Designed to Control 2 Different Electrical Circuits at the same time, which allows the Appliances to Isolate safely and reliably. Fan or light Combinations and Medical Equipment are some of the many applications for DP Electrical Switches and Electrical components.

02. Timer:

A timer is a type of time-switching device that controls and controls Electrical circuits and electrical and electronic devices through time setting (on/off). The timer is basically 8-pin. Like other controlling devices the timer has a coil and when this coil is magnetized, the timer works on/off. The timer has 2 common ends and each common end has normally close and normally open options. When the timer is set by time, the timer trips at the end of that time and turns the common is normally closed (on) to open (off) and normally open (off) to close (on). This is how the timer works.

03. Indicator Light:

An indicator lamp just Sounds Technical, Sometimes it is called a Supervisory light Indicator. Indicator lights are amber in color and can be located at the Front, the Rear, and Sometimes at the Side of the car on both the left And Right-hand sides. The Common colors used by Indicator lamps are red, yellow, blue, white, and green line system. A Panel Indicator Lamp Generally has up to 5 Differently Colored Segments to Indicate Various Conditions on the Machine or Process system.

Thank You for visiting the website. Keep visiting for more Updates.

Frequently asked questions

How does a relay timer work?

Upon application of the input voltage, the time delay relay was ready to accept a trigger. When the trigger was applied, the time delay (t1) begins. At the end and of the time delay (t1), the output is energized. When the triggers are removed, the output contacts remain energized of the time delay (t2).

Where are timer relays used?

Timing relays are commonly used in a variety of industrial and commercial applications. Some of the common applications include machines, buildings, water segments, HVAC, by other applications.

What is the difference between a control relay and a timer relay?

On the conventional Control Relay, the contacts are opened-closed when a voltage is applied and removed for the coil, however, for timer relays the contacts would open or close before or after an intentional period.

How many types of timer relays are there?

On- and off-delay timers the represent most typical time delay relay timers in use. Other types include interval-on-operate, flasher, or repeat cycle timers. Normally open, on-delay timers start timing when the input voltage (power) is applied.

How do you control a relay?

For example, the relay may be controlled by a low-voltage, low-current supply signal that passes through a delicate switch of some sort (e.g. limit switch, proximity switch, optical sensor), and then the switching contacts of that relay may be used to control a much higher-voltage, higher-current flow circuit, and even multiple.

Read more Single Phase Wiring


Submit a Comment

Your email address will not be published. Required fields are marked *