Automatic Changeover Switch wiring diagram:

This diagram shows how to make Automatic Changeover Switch wiring. In this circuit, we use 2 DP MCBs ( Double Pole Miniature Circuit Breaker ), a power generator, 6 SP MCBs ( Single Pole Miniature Circuit Breaker ), and a changeover switch. This circuit diagram is very simple and easy to make it. If you want to clear details about this circuit please check our youtube video below the post.


Diagram of Automatic Changeover Switch wiring diagram:

Automatic Changeover Switch wiring diagram

Components needed For this Project:

You can get the components from any of the sites below:

  1. DP MCB 32A [See Buy Click Amazon]
  2. Dual Power ATS Generator Changeover [See Buy Click Amazon]
  3. Single Phase Generator 2000W[See Buy Click Amazon]
  4. SP MCB 10A [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:


Components used to make the Automatic Changeover Switch wiring diagram:

01. DP MCB:

DP MCB In 2 Pole MCB, switching & protection is affected in phases and the neutral. A Double Pole or DP Switch is a Switch that Controls 2 Circuits at the same time. In terms of Residential Switching, this Normally means it Switches the live and Neutral at the same time. In Layperson Terms, Double Pole switches or DP Switches are Exclusively Designed to Control 2 Different Electrical Circuits at the same time, which allows the Appliances to Isolate safely and reliably. Fan or light Combinations and Medical Equipment are some of the many applications for DP Electrical Switches and Electrical components.

02. Changeover Switch:

Change over switch is a medium of line transfer that is used in industry. Every industry has a supply line using change-over switches to supply power. A Changeover Switch is an Electrical Switch That Allows a load to be Changed from one Electrical Source to Another and vice Versa, Either Manually or Automatically. A Changeover Switch is specially made to transfer a house is electricity from the Normally used Commercial Power supply grid to a more local Generator when a power Outage Occurs.

03. Power Generator:

An electric generator is a type of Electrical device that converts mechanical energy or power into electrical energy or power. However, dynamo generally refers to generators only. The first generator built was called a dynamo. This electrical device makes this conversion using the principle of kinetic electromagnetic energy generation. According to Farad is principle of electromagnetic induction, a dynamic electromagnetic induction is induced in a conductor when it passes through a magnetic flux.

04. SP MCB:

In single-pole MCB, Switching and protection are Affected in only one Phase. Single phase supply to break the phase only. A single Pole breaker is Typically used with 120-volt Circuits, and a 6-20 amps Miniature Circuit Breaker. They are constructed with one Line Wire and one Neutral wire. A Single Pole switch is the most basic General-Purpose switch that you use to Control a light or another device from one location. These Switches have 2 Brass-Colored screw Terminals Connected to the hot Power source wires. Pole refers to the number of Circuits Controlled by the Switch SP Switches Control only one Switch Electrical Circuit.

Thank You for visiting the website. Keep visiting for more Updates.

Frequently asked questions

What is the principle of a 3-phase automatic transfer switch?

The transfer switch shifts the load to the emergency power supply source when power from the generator or backup utility feed is stable and within prescribed voltage and frequency tolerances. Depending on a facility's needs and preferences, the Circuit diagram transfer process is self-acting or manually initiated.

What are the two types of automatic transfer switches?

There are 2 types of automatic transfers and switches, circuit diagram breakers, and contactors. The circuit diagram breaker type has two interlocked circuit breakers, so only one breaker can be closed at any anytime.

What are the applications of automatic changeover switches?

Automatic and Changeover Switches are used in residential settings to switch between the main utility power supply and backup generators. They provide homeowners with an uninterrupted power supply during power outages, ensuring the project system's functioning of essential appliances and systems.

What are the features of a changeover switch?

Thus, the changeover switch ensures continuity of supply to the load by alternating between normal and alternate supply. The switch is in the ON position with normal supply available at the outgoing terminals. The switch is in the ON position with an alternate supply available at the outgoing terminals.

What is the difference between a manual transfer switch and ATS?

Unlike a manual transfer switch, automatic transfer switches can be used with permanently installed standby and generators. That way, when your power supply is disrupted and your company is subject to blackouts, your generator will automatically kick on and supply an emergency backup power supply to your building.

Read more Single Phase Wiring


Submit a Comment

Your email address will not be published. Required fields are marked *