Digital timer switch wiring:

This diagram shows how to make a digital timer switch wiring diagram. In this circuit, we use a digital timer, a DP MCB ( Double Pole Minature Circuit Breaker ), a magnetic contactor, and a TP MCB ( Tripple Pole Minature Circuit Breaker ). First, we need to connect the TP MCB with the power source, then connect the magnetic contactor with the TP MCB, then connect the DP MCB with the power source, then connect the timer with the power source. Now this circuit is ready for use.

Diagram of Digital timer switch wiring:

Components needed For this Project:

You can get the components from any of the sites below:

DP MCB 16A [See Buy Click Amazon]
TP MCB 20A [See Buy Click Amazon]
Magnetic Contactor 40A [See Buy Click Amazon]
8 Pin Timer 220V AC [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

Components used to make the Digital timer switch wiring:

01. DP MCB:

DP MCB In 2 Pole MCB, switching & protection is affected in phases and the neutral. A Double Pole or DP Switch is a Switch that Controls 2 Circuits at the same time. In terms of Residential Switching, this Normally means it Switches the live and Neutral at the same time. In Layperson Terms, Double Pole switches or DP Switches are Exclusively Designed to Control 2 Different Electrical Circuits at the same time, which allows the Appliances to Isolate safely and reliably. Fan or light Combinations and Medical Equipment are some of the many applications for DP Electrical Switches and Electrical components.

02. TP MCB:

The full meaning of MCB is Miniature Circuit Breaker for TP MCB. MCB is an electromagnetic switch or device. If for any reason a short circuit occurs in the supply line or load line (line to line or line to neutral) or in case of overload MCB. the MCB automatically trips and disconnects the main line circuit or household power supply Connection. TP MCB In 3 Pole MCB, Switching & Protection is affected in only 3-Phases and the Neutral is not part of the MCB. 3 pole MCB signifies the Connection of Three Wires for a 3-Phase system Red-Yellow-Blue Phase. 3-Phase Supply Only Without Neutral.

03. Magnetic Contactor:

A magnetic contactor is an electromagnetic switching device. It is generally used for controlling 3-phase Motors. The operation of a magnetic contactor is similar to that of a Relay. but a relay is used for low-power or low-voltage connections, and a magnetic contactor is used for high-power or high-voltage connections. As soon as the supply is applied to the magnetic contactor coil. its normally open contacts are closed and normally closed contacts are opened and the associated devices are also operated. This is how a magnetic contactor works.

04. Timer:

A timer is a type of time-switching device that controls and controls Electrical circuits and electrical and electronic devices through time setting (on/off). The timer is basically 8-pin. Like other controlling devices the timer has a coil and when this coil is magnetized, the timer works on/off. The timer has 2 common ends and each common end has normally close and normally open options. When the timer is set by time, the timer trips at the end of that time and turns the common is normally closed (on) to open (off) and normally open (off) to close (on). This is how the timer works.

Thank You for visiting the website. Keep visiting for more Updates.

Frequently asked questions

How is a timer switch wired?

Some digital time switches will have screw terminals to which the circuit diagram wires are connected, while other switches have wire leads that are connected to the circuit diagram wires with wire connectors. Most typically, there are 3 wire leads: a green ground lead, a black LINE lead, and a white neutral lead.

What is a load wire on a timer switch?

A load wire on a timer switch is the wire that carries the electrical current to the device that the switch controls. In the context of a timer switch, the load wire connects to the electrical load, such as a light or an appliance, that the switch is intended to control.

How switches are wired?

The feed wire (the hot wire coming from the service panel) runs off the switch before it goes to the fixture. 2 cables enter the switch of the box: one supplying the power supply and one going to the fixture. The neutral wires were spliced, and a black wire connected to each switch terminal.

What is a digital timer socket?

Using a plug-through system, a socket with a timer setup means that the chosen device or appliance is plugged into it, which in turn is inserted into a standard socket outlet. A timer socket is a great way to control lighting, televisions, or radios, enabling them to be operated to a pre-set time or schedule.

Do light timers use electricity?

A light timer is an electrical circuit diagram with a built-in clock. It acts as a communicator between the power supply source and the light. The timer can turn the lights on or off based on the time you set.

← Previous Next →

Digital timer switch wiring