Save electricity wiring | What you can do to save electricity

Electrical, single phase Line Wiring | 0 comments

Basic Electrical
Power System
House Wiring
Motor Wiring
Industrial Wiring
Basic Electronic
Electronic Project
Electronic Mini Project
Digital Logic Gate
Arduino Project
Microcontroller Board
Electronic Sensor
Electronic Module
Electronic Display

What you can do to save electricity | Save electricity wiring:

This diagram shows how to make save electricity wiring. In this circuit diagram, we explain how can you save your electricity and how can improve the power factor in your house. In this circuit, we use a single-phase energy meter, a TP MCB ( Tripple Pole Miniature Circuit Breaker ), and four 400V 2.50uf capacitors. First, we need to connect the input power to the energy meter, then the input line to all capacitors like in our diagram, then input the power to TP MCB, and then input power to home loads from TP MCB. Now our circuit is ready for use. If you want to know more about this circuit please check our youtube video below the post.

Advertisements

Diagram of Save electricity wiring:

Save electricity wiring

Components needed For this Project:

You can get the components from any of the sites below:

  1. Single Phase Energy Meter [See Buy Click Amazon]
  2. TP MCB 20A [See Buy Click Amazon]
  3. PFI Capacitor 25UF [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

Advertisements

Components used to make the Save electricity wiring:

01. Single Phase Energy Meter:

A Single-Phase Energy Meter is a sort of Watt-Hour meter. It consists of two Electromagnets. Single-Phase Energy Meter is also Popularly known as a watt-hour meter. 1 Magnet is called the shunt magnet Ml which is Mounted with a Pressure coil. The Pressure coil is a long coil Made of fine Copper wire that is connected across the Supply single-phase line. Single-phase energy meters are suitable for measuring single-phase AC current flow frequencies of 50/60 Hz, which are used for fixed indoor installation systems.

02. TP MCB:

The full meaning of MCB is Miniature Circuit Breaker for TP MCB. MCB is an electromagnetic switch or device. If for any reason a short circuit occurs in the supply line or load line (line to line or line to neutral) or in case of overload MCB. the MCB automatically trips and disconnects the main line circuit or household power supply Connection. TP MCB In 3 Pole MCB, Switching & Protection is affected in only 3-Phases and the Neutral is not part of the MCB. 3 pole MCB signifies the Connection of Three Wires for a 3-Phase system Red-Yellow-Blue Phase. 3-Phase Supply Only Without Neutral.
03.PFI Capacitor:

Power factor correction capacitors are an efficient and simple solution to low power factor issues 0.9pf system. A capacitor or bank of capacitors installed parallel to the load provides this reactive power supply. A power factor improvement plant or PFI (KVR) is designed to reduce the gap between real power and apparent power supply. The Inductive load such as transformer(3 Phase), induction motors, etc. is because of the low power factor.

Thank You for visiting the website. Keep visiting for more Updates.

Frequently asked questions

Which wire saves electricity?

A 10 gauge wire of the same length only loses 48 watts of energy when delivering the power supply same load of current. Over time, larger electrical wire lowers your overall energy costs because less energy is being lost in your electrical project system.

What is electrical wiring safety?

Electrical safety is a general practice of handling and maintaining electrically powered supply equipment to prevent incidents. Adequate training is required to properly identify and control hazards to keep the Circuit diagram environment safe for those around. Whether you're at work or at home,as both settings operate on electricity.

How to do safety wiring?

The process is simple. You insert the wire through the fasteners to be fastened, insert a ferrule on the end, insert the wire end through the power supply of the tool, and put some tension on the wire. You then squeeze the tool's handle to crimp the end and cut the wire in 1 step.

How do you check wires for power?

The most common option is a contact and voltage tester, which uses 2 metal probes to test the flow of electricity. There are also 1-contact voltage testers that can detect an electrical current from about an inch away, instead of coming into direct contact with the Project system outlet or exposed wiring.

What is electrical wiring installation?

An electrical installation is a group of items of electrical equipment that are permanently electrically connected together and can be supplied with electricity Currenttlou from the works of an electricity entity or from a generating source. An item of electrical and equipment may be part of more than 1 electrical installation.

Read more Single Phase Wiring

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *


Join our Youtube Channels to stay updated with the latest Electronic and Electrical Projects and exclusive updates.


Electronic Experiment Youtube Channel: Join Now

Advertisements