Star Connection Diagram:

This diagram shows how to make Star Connection Diagram. In this circuit, we use DP MCB ( Double Pole Minature Circuit Breaker ), 3 magnetic contactors, an overload relay, and an indicator light. First, we need to connect the DP MCB with the power source, then connect all contactors with the power source, then connect the indicator light. Now this circuit is ready for use.

Diagram of Star Connection:

Components needed For this Project:

You can get the components from any of the sites below:

DP MCB 10A [See Buy Click Amazon]
Magnetic Contactor 40A [See Buy Click Amazon]
Motor Protector Overload [See Buy Click Amazon]
Indicator Light 220v AC [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

Components used to make the Star Connection Diagram:

01. DP MCB:

DP MCB In 2 Pole MCB, switching & protection is affected in phases and the neutral. A Double Pole or DP Switch is a Switch that Controls 2 Circuits at the same time. In terms of Residential Switching, this Normally means it Switches the live and Neutral at the same time. In Layperson Terms, Double Pole switches or DP Switches are Exclusively Designed to Control 2 Different Electrical Circuits at the same time, which allows the Appliances to Isolate safely and reliably. Fan or light Combinations and Medical Equipment are some of the many applications for DP Electrical Switches and Electrical components.

02. Magnetic Contactor:

A magnetic contactor is an electromagnetic switching device. It is generally used for controlling 3-phase Motors. The operation of a magnetic contactor is similar to that of a Relay. but a relay is used for low-power or low-voltage connections, and a magnetic contactor is used for high-power or high-voltage connections. As soon as the supply is applied to the magnetic contactor coil. its normally open contacts are closed and normally closed contacts are opened and the associated devices are also operated. This is how a magnetic contactor works.

03. Overload Relay:

Overload Protection is Protection Against a Running Overcurrent That Would Cause Overheating of The Protected Equipment. Hence, An Overload is Also a Type of Overcurrent flow. Overload Protection Typically Operates on an Inverse Time curve where the Tripping Time Becomes less as the Current Increases. This Overload Protector is an Essential Component for Many Sockets Power Systems. The Top-Quality Overload Protector can Effectively Protect Electrical Products from Power Surges.

04. Indicator Light:

An indicator lamp just Sounds Technical, Sometimes it is called a Supervisory light Indicator. Indicator lights are amber in color and can be located at the Front, the Rear, and Sometimes at the Side of the car on both the left And Right-hand sides. The Common colors used by Indicator lamps are red, yellow, blue, white, and green line system. A Panel Indicator Lamp Generally has up to 5 Differently Colored Segments to Indicate Various Conditions on the Machine or Process system.

Thank You for visiting the website. Keep visiting for more Updates.

Frequently asked questions

What is phase voltage in a star connection?

Phase Voltage was the potential difference between a phase and the neutral junction. 3. In the star connection, the line voltage was √3 times the phase voltage. In the star connection, the phase voltage was 1/√3 times the line voltage. For the Delta connection, the line voltage and phase voltage were equal.

Why is the star connection used?

Generally, a star connection is used where you need a neutral and two separate voltages, like our distribution system. Delta connection is generally preferred where the neutral conductor is not needed like for transmission of high-voltage power.

What is the star or Y connection?

In a Star Connection, the three-phase wires are connected to a common point or star point, and Neutral was taken from this common point. Due to its shape, the star connection is sometimes also called a Y or Wye connection. If only the three-phase wires are used, then it is called 3 Phase 3 Wire system.

Where is the star connection used?

A star connection is commonly used in electrical device engineering and networking. In electrical engineering, a star connection is used in 3-phase electrical systems to connect multiple electrical devices.

What is called a star connection?

A star connection was a connection used in a polyphase electrical device in which the windings each have one end connected to a common junction and the other end to a separate terminal.

← Previous Next →

Star Connection Diagram