3 Phase Distribution Board In MCCB Wiring:

This diagram shows how to make 3 Phase Distribution Board In MCCB Wiring. In this circuit, we use a TP MCCB ( Tripple Pole Molded Case Circuit Breaker ), three-ampere meters, two voltmeters, three lamps, and three TP MCB ( Tripple Pole Miniature Circuit Breaker ). This circuit is very simple and easy to make. If you want to know more about this circuit please check our youtube video below the post.

Diagram of 3 Phase Distribution Board In MCCB Wiring:

Components needed For this Project:

You can get the components from any of the sites below:

TP MCB 20A [See Buy Click Amazon]
single phase Volt Meter [See Buy Click Amazon]
Single Phase Amperemeter [See Buy Click Amazon]
MCCB 63A [See Buy Click Amazon]
CT Transformer [See Buy Click Amazon]
Indicator Light 220v AC [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

Components used to make the 3 Phase Distribution Board In MCCB Wiring:

01. TP MCB:

The full meaning of MCB is Miniature Circuit Breaker for TP MCB. MCB is an electromagnetic switch or device. If for any reason a short circuit occurs in the supply line or load line (line to line or line to neutral) or in case of overload MCB. the MCB automatically trips and disconnects the main line circuit or household power supply Connection. TP MCB In 3 Pole MCB, Switching & Protection is affected in only 3-Phases and the Neutral is not part of the MCB. 3 pole MCB signifies the Connection of Three Wires for a 3-Phase system Red-Yellow-Blue Phase. 3-Phase Supply Only Without Neutral.

02. Voltmeter:

An instrument that measures the potential difference between any two points in a circuit directly in volts is called a voltmeter. A voltmeter is an Electrical instrument that directly measures the potential difference between any 2 points in a circuit in volts. The voltmeter is connected in parallel with the 2 points in the circuit where the potential difference is to be measured. This instrument consists of a galvanometer. Like an electric cell or an ammeter, a voltmeter has 2 terminals, a positive and a negative terminal. Usually, the positive end is red and the negative end is black.

03. Ampere Meter:

Ammeter, an instrument, with the help of which the flow of electricity can be measured directly in Electrical units, amperes. It is a galvanometer with very low resistance. As a result, the entire current flows through the meter coil. Current is measured with an ammeter. So it can be said that the device that measures the flow of current in an ampere unit is an ammeter. Electric current is the flow of electrons whose unit is an ammeter. So it can be said that the device that measures the flow of current in an ampere unit is an ammeter. An ideal ammeter has no internal resistance. But in reality. the ammeter has little internal resistance. The range of the ammeter depends on this resistance.

04.MCCB:

The full meaning of MCB is Miniature Circuit Breaker. MCB is an electromagnetic switch or device. If for any reason a short circuit occurs in the supply line or load line (line to line or line to neutral) or in case of overload, the MCB automatically trips and disconnects the main line circuit or household power Connection. TP MCB In Three Pole MCB, Switching & Protection is affected in only Three-Phases and the Neutral is not part of the MCB. 3 pole MCB signifies the Connection of Three Wires for a Three-Phase system R-Y-B Phase. Three-Phase Supply Only Without Neutral.

05. CT Coil:

A current Transformer is a device used to measure alternating currents. The transformer used with the ammeter for high-quality AC current measurement is called a current transformer abbreviated as CT. Current transformers are mainly used to measure high current flow. We know that high power lines carry a lot of currents. In this case, an ordinary ammeter or multimeter cannot measure this current flow. Current transformers are used in Acorn.

06. Indicator Light:

An indicator lamp just Sounds Technical, Sometimes it is called a Supervisory light Indicator. Indicator lights are amber in color and can be located at the Front, the Rear, and Sometimes at the Side of the car on both the left And Right-hand sides. The Common colors used by Indicator lamps are red, yellow, blue, white, and green line system. A Panel Indicator Lamp Generally has up to 5 Differently Colored Segments to Indicate Various Conditions on the Machine or Process system.

Thank You for visiting the website. Keep visiting for more Updates.

Frequently asked questions

How do you balance a 3-phase distribution board?

Three-phase load balancing occurs when loads of power supplies, such as a three-phase rack PDU, are spread evenly across all 3 phases (L1/L2, L2/L3, and L3/L1). It can be achieved by having an equal number of devices plugged into PDU outlets for each phase and drawing an equal power supply load on each phase.

What is a balanced and unbalanced load in a 3-phase system?

A balanced 3-phase load refers to a condition when all 3 phases carry the same magnitude of current flow along with the same phase differences. This is due to the loads having equal magnitudes and phase angles. An unbalanced load refers to the condition when unequal current diagrams are carried by the 3 phases.

What is a 3-phase distribution board?

Three-phase distribution boards are panels that house the circuit diagram breakers, ground leakage protection units, and fuses that are used to distribute power to individual consumer points or circuit diagrams within a building.

Why is a three-phase system distribution board important?

A three-phase circuit diagram provides greater power density than a one-phase circuit at the same amperage, keeping wiring size and costs lower. In addition, a three-phase power supply makes it easier to balance loads, minimizing harmonic current flow and the need for large neutral wires.

What is the reason for the distribution board?

A distribution board or distribution panel board (DP) is an important part of an electricity supply system. Its job is to split an incoming electrical power supply feed into multiple secondary or subsidiary circuit diagrams Most of the time, each of these secondary circuit diagrams will be protected with a fuse or breaker.

← Previous Next →

3 Phase Distribution Board In MCCB Wiring