Simple Music Player With Buzzer

Music player Buzzer

This is a simple project that will allow you to play music on your Arduino using a buzzer and some LEDs. Depending on the frequency, a different LED will light.

Components Parts needed

Arduino Uno : [ See Buy Click Banggood | Amazon ]
4 LED [ See Buy Click Banggood | Amazon ]
230 ohms and 470 ohms [ See Buy Click Banggood | Amazon ]
Jump Wires [ See Buy Click Banggood | Amazon ]
Breadboard [ See Buy Click Banggood | Amazon ]
Push-Button switch [ See Buy Click Banggood | Amazon ]
Buzzer [ See Buy Click Banggood | Amazon ]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Circuit Schematics

simple-music-player-with-buzzer-circuit-min

Source Codes


//Use pushbotton as a toggle switch.
//website : https://earthbondhon.com/simple-music-player-with-buzzer/
//When the pushbotton is pressed, the pushbotton pin reads a
//high voltage and then a low voltage, and then ledOn is set
//to the opposite of its current value (either false or true).

//Based on Starter Kit Project 02.
#include "pitches.h"

const int piezoPin = 12; //piezo
const int rPin = 5;  //red LED
const int gPin = 4;  //green LED
const int bPin = 3;  //blue LED
const int pPin = 2;  //pushbutton

int ledState = 0;
int ledOn = false;

// notes
int melody[] = {
  NOTE_F5,NOTE_D5,NOTE_AS4,NOTE_D5,NOTE_F5,NOTE_AS5,NOTE_D6,NOTE_C6,NOTE_AS5,NOTE_D5,NOTE_E5,NOTE_F5,
  NOTE_F5,NOTE_F5,NOTE_D6,NOTE_C6,NOTE_AS5,NOTE_A5,NOTE_G5,NOTE_A5,NOTE_AS5,NOTE_AS5,NOTE_F5,NOTE_D5,NOTE_AS4,
  NOTE_D6,NOTE_D6,NOTE_D6,NOTE_DS6,NOTE_F6,NOTE_F6,NOTE_DS6,NOTE_D6,NOTE_C6,NOTE_D6,NOTE_DS6,NOTE_DS6,
  0,NOTE_DS6,NOTE_D6,NOTE_C6,NOTE_AS5,NOTE_A5,NOTE_G5,NOTE_A5,NOTE_AS5,NOTE_D5,NOTE_E5,NOTE_F5,
  NOTE_F5,NOTE_AS5,NOTE_AS5,NOTE_AS5,NOTE_A5,NOTE_G5,NOTE_G5,NOTE_G5,NOTE_C6,NOTE_DS6,NOTE_D6,NOTE_C6,NOTE_AS5,NOTE_AS5,NOTE_A5,
  NOTE_F5,NOTE_F5,NOTE_AS5,NOTE_C6,NOTE_D6,NOTE_DS6,NOTE_F6,NOTE_AS5,NOTE_C6,NOTE_D6,NOTE_DS6,NOTE_C6,NOTE_AS5
};

// durations: 2 = half note, and 8/3,4,6,8,12. It appears that 8/2.9 is more accurate than 8/3.
float noteDurations[] = {
  6,12,4,4,4,2,6,12,4,4,4,2,
  8,8,8/2.9,8,4,2,8,8,4,4,4,4,4,
  6,12,4,4,4,2,8,8,4,4,4,2,
  8,8,8/2.9,8,4,2,8,8,4,4,4,2,
  4,4,4,8,8,4,4,4,4,8,8,8,8,4,4,
  8,8,8/2.9,8,8,8,2,8,8,4,4,4,2
};

// calculates the number of elements in the melody array.
int musicLength=sizeof(melody)/sizeof('NOTE_F5');

void setup() {  
  pinMode(pPin, INPUT);
  pinMode(rPin, OUTPUT);
  pinMode(gPin, OUTPUT);
  pinMode(bPin, OUTPUT);
}

void loop() {
  int pPinState=digitalRead(pPin);
  if(pPinState==HIGH) {
    ledState = 1;
  }
  if (pPinState==LOW and ledState ==1) {
    ledState = 2;
    ledOn = not ledOn;
  }
  if (ledOn && pPinState!=HIGH) {
    for (int thisNote = 0; thisNote < musicLength; thisNote++) {
      // blink the three LEDs in sequence
      if (thisNote%3==0){    
        digitalWrite(rPin, HIGH);
        digitalWrite(gPin, LOW);
        digitalWrite(bPin, LOW);
      }
      else if (thisNote%3==1){    
        digitalWrite(rPin, LOW);
        digitalWrite(gPin, HIGH);
        digitalWrite(bPin, LOW);
      }
      else if (thisNote%3==2){    
        digitalWrite(rPin, LOW);
        digitalWrite(gPin, LOW);
        digitalWrite(bPin, HIGH);
      }

      // calculate the note duration. change tempo by changing 2000 to other values
      int noteDuration = 2000/noteDurations[thisNote];
      tone(piezoPin, melody[thisNote],noteDuration);
      
      // to distinguish the notes, set a minimum time between them.
      // the note's duration + 30% seems to work well
      float pauseBetweenNotes = noteDuration * 1.30;
      
      //split the delay into two parts and check to see
      //whether the pushbutton is pressed to turn off
      //the sound and light
      delay(pauseBetweenNotes/2);
      if(digitalRead(pPin)==HIGH) {
        break;      
      }
      delay(pauseBetweenNotes/2);
      if(digitalRead(pPin)==HIGH) {
        break;      
      }
    }
  }
  else if (not ledOn) {
    digitalWrite(rPin, LOW);
    digitalWrite(gPin, LOW);
    digitalWrite(bPin, LOW);
  }
}

Simple Music Player With Buzzer

Music player Buzzer

Components Parts needed

Circuit Schematics

Source Codes

Watch to Youtube Video

Read more Arduino Project

Join our Youtube Channels to stay updated with the latest Electronic and Electrical Projects and exclusive updates.

Electronic Experiment Youtube Channel: Join Now

Submit a Comment Cancel reply

All Topics

About Earth Bondhon

Contact

All Topics of Site

Help

Copyright © 2016-2023 | All Right Reserved.